![]() If /opt/MegaCli does not exist, create that folder.Copy this “image” folder via WinSCP (or other application) onto the ESXi-Server into the following directory: /opt/MegaCli.Extract the “image” folder from that file.Download the attached ibm_fw_sraidmr_6gb-23.34.0-0018_linux_32-64.bin (see attached files).- Assign an IP-Address (to be able to connect via SSH later on).ESXi will be running within the RAM (root password is blank).Remove the boot-option „runweazel“ in the command-line and press Enter to boot the ISO Image into the RAM.During the boot process (booting from ISO), press “Shift+O”.Boot from Vmware ISO image (doesn’t matter which version – 5.5 or 6.0 or 6.5).The following workaround fixed my problem: The following error was shown during the Installation of ESXi:Ĭommand '/sbin/partedUtil setptbl /vmfs/devices/disks/naa.60.Įrror: Input/output error during read on /dev/disks/naa.60. We had the same issue with IBM x3650 M4 ServeRaid M5110e Firmware 23.34.0-0023. This is the first time this has ever happened to us and we are at lost and praying for ideas. The DSA, IMM2 and UEFI versions running are shown below. I even tried to install 6.0 U2 using the Lenovo custom image. VMware recommended we rebuilt the RAID configuration and try to do a clean install of ESXi 5.5 U3 using the Lenovo custom image. Everything was working fine before we upgraded the firmwares. We contacted VMware and they suspected something was wrong with the storage on this server. It was a RAID1 composed of 2 HDD and 1 Hot Spare. Doing so, it upgraded the RAID controller firmware to version 23.31.0-0023.Īfter the upgrade, the host booted but the local datastore didn't mount and gave an error when trying to mount it. Tip: You can remove the Boot Disk Media at any time after boot-up and insert the media where you have stored your driver files to be loaded.We were in the process of upgrading our ESXi 5.1 to 5.5 U3 and before we were upgrading the firmware on our IBM System x3650 M4 servers using the IBM BOMC. You should now be able to access your hard drives after the driver is successfully loaded. During the boot process, these drivers will be loaded automatically. Clicking on the INF file will load the drivers.Ĭreate a folder called Bootdisk_Drivers on the root of any drive that will be visible after boot (without requiring the extra drivers) and copy the required files to that folder. The dialog allows you to browse to the location of where you stored the driver INF and accompanying SYS files. Once booted into Boot Disk, Click on the Start menu, then select "Load Driver". These will be saved to the bootable media and automatically loaded when booting your system up. When running the Boot Disk Creator add the driver INF and accompanying SYS files to the "Add Drivers" section. Once you have downloaded the drivers, you may load them in one of three ways. ![]() You will need to download the 64-bit drivers as the Boot Disk environment is based on a 64-bit version of Windows. The manufacturer's support pages are also the location of where you can download the drivers for your system. Whether you have a Dell, HP, Sony, Gateway or other brand of system, the manufacturer's support pages will identify what controller you have based on your system's model number or other service identifying number. You can look that up in the properties of My Computer - Device Manager - under IDE ATA controllers or under Storage controllers.Īnother way is to look up the specifications of your computer from the manufacturer's web page. In this case, you can add or load additional drivers yourself.įirstly, you will need to identify the type of hard drive controller you have in your computer. Suggestions: The set of common drivers in Boot Disk may not include the driver for your hard drive controller. The Boot Disk cannot see the drives in my system, what can I do so they would be detected?
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |